What is Resistor?
Resistor is defined as
A passive electrical component with two terminals that are used for either limiting or regulating the flow of electric current in electrical circuits.
The main purpose of resistor is to reduce the current flow and to lower the voltage in any particular portion of the circuit. It is made of copper wires which is coiled around a ceramic rod and the outer part of the resistor is coated with an insulating paint.
What is the SI Unit of Resistor?
The SI unit of resistor is Ohm.
The resistor is a passive electrical component that creates resistance in the flow of electric current. In almost all electrical networks and electronic circuits they can be found. The resistance is measured in ohms (Ω). An ohm is the resistance that occurs when a current of one ampere (A) passes through a resistor with a one volt (V) drop across its terminals. The current is proportional to the voltage across the terminal ends. This ratio is represented by Ohm’s law:
Resistors are used for many purposes. A few examples include limiting electric current, voltage division, heat generation, matching and loading circuits, gain control, and setting time constants. They are commercially available with resistance values over a range of more than nine orders of magnitude. They can be used as electric brakes to dissipate kinetic energy from trains, or be smaller than a square millimeter for electronics.
Resistor Definition and Symbol
A resistor is a passive electrical component with the primary function to limit the flow of electric current.
The international IEC symbol is a rectangular shape with leads at each end as shown in the figure at left. In the USA, the ANSI standard is very common and represents a fixed resistor as a zigzag line (shown on the right).
IEC fixed resistor symbol
ANSI fixed resistor symbol
Overview of Types and Materials
Resistors can be divided by functional type as well as resistance material. The following breakdown for the types can be made:
- Fixed resistors
- Variable resistors, such as the:
- Resistors for which the resistance value is dependent on a physical quantity:
- Thermistors (NTC and PTC) – the resistance is a function of temperature
- Photo resistors – the resistance is a function of light level
- Varistors – the resistance is a function of voltage
- Magneto resistors – the resistance is a function of magnetic field
- Strain gauges – the resistance is a function of mechanical load
For each of these types, a standard symbol exists. Another breakdown based on the material and manufacturing process can be made:
- Carbon composition
- Carbon film
- Metal film
- Metal oxide film
The choice of material technology is specific to the resistor purpose. Often it is a trade-off between cost, precision, power, and other requirements. For example, carbon composition is a very old manufacturing technique that creates a low precision resistor, but is still used for specific applications where high energy pulses occur. Carbon composition resistors have a body made from a mixture of fine carbon particles and a non-conductive ceramic.
The carbon film technique creates resistors with a better tolerance (less resistance value variation) than carbon composition resistors. These are made of a non-conductive rod with a thin carbon film layer around it. This layer is treated with a spiral cut to increase and control the resistance value.
Metal and metal oxide film are widely used nowadays, and have better properties for stability and tolerance. Furthermore, they are less influenced by temperature variations. Like carbon film resistors, they are constructed with a resistive film around a cylindrical body. Metal oxide film is generally more durable.
Wirewound resistors are probably the oldest type and can be used for both high precision as well as high power applications. They are constructed by winding a special metal alloy wire, such as nickel chrome, around a non-conductive core. They are durable, accurate, and can have very low resistance value. A disadvantage is that they suffer from parasitic reactance at high frequencies.
For the highest requirements on precision and stability, metal foil resistors are used. They are constructed by cementing a special alloy cold rolled film onto a ceramic substrate.
Dependent on the application, the electrical engineer specifies different properties of the resistor. The primary purpose is to limit the flow of electrical current; therefore the key parameter is the resistance value. The manufacturing accuracy of this value is indicated with the resistor tolerance and is expressed as a percentage of the resistance value (for example ±5%). Many other parameters that affect the resistance value can be specified, such as long term stability or the temperature coefficient. The temperature coefficient, usually specified in high precision applications, is determined by the resistive material as well as the mechanical design.
In high frequency circuits, such as in radio electronics, the parasitic capacitance and inductance can lead to undesired effects. Foil resistors generally have a low parasitic reactance, while wirewound resistors are among the worst. For accurate applications such as audio amplifiers, the electric noise of the resistor must be as low as possible. This is often specified as microvolts noise per volt of applied voltage, for a 1 MHz bandwidth. For high power applications the power rating is important. This specifies the maximum operating power the component can handle without altering the properties or damage. The power rating is usually specified in free air at room temperature. Higher power ratings require a larger size and may even require heat sinks. Many other characteristics can play a role in the design specification. Examples are the maximum voltage or the pulse stability. In situations where high voltage surges could occur, this is an important characteristic.
Sometimes not only the electrical properties are important, but the designer also has to consider the mechanical robustness in harsh environments. Military standards sometimes offer guidance to define the mechanical strength or the failure rate.
Many standards exist for resistors. The standards describe ways to measure and quantify important properties. Other norms exist for the physical size and resistance values. Probably, the most well known standard is the color code marking for axial leaded resistors.
Resistor color code
The resistance value and tolerance are indicated with several colored bands around the component body. This marking technique of electronic components was already developed in the 1920s. Printing technology was still not far developed, what made printed numerical codes too difficult on small components. Nowadays, the color code is still used for most axial resistors up to one watt. In the figure above, an example is shown with four color bands. In this example the two first bands determine the significant digits of the resistance value, the third band is the multiplying factor and the fourth band gives the tolerance. Each color represents a different number and can be looked up in a resistor color code chart or using a resistor color code calculator.
Resistor color code calculator
The color code can easily be decoded using this calculator.
Resistor Values (Preferred values)
In the 1950s, the increased production of resistors created the need for standardized resistance values. The range of resistance values is standardized with so called preferred values. The preferred values are defined in E-series. In an E-series, every value is a certain percentage higher than the previous. Various E-series exist for different tolerances.
keep in touch with our social media links as mentioned below
Mifratech Note : Find the best solution for electronics components and technical projects ideas
Contact for more information : [email protected] / 080-73744810 / 9972364704
mifratech instagram : https://www.instagram.com/mifratech/
mifratech twitter account : https://twitter.com/mifratech
Tweets by mifratech
#bestelectroniccomponentsnearme #bestcomponentsshoparoundme #topeelectroniccomponentsshop
#lcdinterfacingwithaurduinouno #lcdinterfacingwithnano #lcdinterfacingwithnodemcu #lcdinterfacingwithraspbeerpi #lcdinterfaingwithnodemcuinbreadeboard #microsdcardmodule
#allengineeringstudentsprojectscomponentsavailable #wholesalepricecomponents #allelectroniccomponentsavailable #bestpricecomponentsstore #allroboticcomponentsavailable #allelectronicscomponentsavailablelike #ARDUINO UNO #RASPBERRYPI #ESP32 #ESP8266 #RFIDMODULERC522 #4X4KEYPAD #microsdcardmodule #cp2102 #arduinopromini #nodemcu #drivercircuit #vibrationsensor #rainsensor #bmp180 #bmp280interfacingwitharduino #ADXL335ACCELEROMETER #soundsensor #5voltsadapter #12voltsadapters #wifismartcamera #moistersensor #watersensor #eyeblinksensor #ultrasonicsensorhcsr04 #currentsensor #voltagesensor #ecgsensormoduleAD8232 #PIRsensor #IRsensor #irproximitysensor #DS18B20tempraturesensor #dht22tempraturesensor #dht11temperaturesensorandhumiditysensor #flamesensor #touchsensor #fluxsensor #allsensorsavailablesofthisstore #9voltsbattery #9voltsbatteryclip #lithineumbatterycell #3.7lithiniumbattery #duresellbattery #16x2LCDdisplay #20x4LCDdisplay #I2Cmodule #LCDkeypadshield #DC-DCconverter #ultrasonicholder #0.98OLEDdisplay #rotaryencoder #12voltsbuzzer #5voltsbuzzer #gassensor #metaldetectorsensor #1channelrelaymodule #2channelrelaymodule #4channelrelaymodule #8channelrelaymodule #16channelrelaymodule #allvaluesofresistor #allvaluesofcapacitors #allvaluesofmosfet #allvaluesofIC`s #3mmleds #flowratesensor #pumpsensormodule #allvaluesofdcmotors #bomotors #bowheels #roboticmotors #roboticwheels #roboticchassis #roboticclamps #roboticscrow #allkindofroboparts #jumperwires #generalpurposewire #solderingirin #solderinglead #solderingflux #multimeter #glowgun #glowstick #cutter #tipesofpushbutton #slidebutton #onofbutton #tongleswitches #alltypesofswitches #alltypesofarduinocables #alltypesofcables #allsizeofsolarpanels #scrowdriverset #complatelyelectroniccomponentsstore
There are no reviews yet.